Maytag washer error codes appear on your appliance when the diagnostic system detects a problem with your washing machine. In most cases, error codes can be cleared easily. In some instances, one or more internal components will need to be repaired or replaced to fix the underlying cause.
This guide walks through the major Maytag washer error codes and gives you instructions on how to fix them. By following these steps, you can often get your washing machine running again quickly.
Maytag washer error codes reference
| Error Code | Meaning | Possible Solution |
|---|---|---|
| LOC, LC | Control Lock activated | Press the Control Lock button |
| dET | Detergent cartridge not detected | Ensure the cartridge is inserted correctly |
| INT | Cycle interrupted | Press the Pause or Cancel button twice, then Power button |
| rL, F34 | Items detected during a Clean Washer cycle | Remove items and restart the cycle |
| Sud or Sd | Excessive suds | Manually remove excess suds and ensure correct detergent usage |
| F5 E2 | Door not locking properly | Check for obstructions and ensure door is closed properly |
| F7 E1 | Motor speed sensing error | Check for shipping bolts and ensure proper load distribution |
| F8 E1, LO FL | Low water flow | Ensure water faucets are turned on and no kinks in hoses |
| F8 E2 | Dispenser system issue | Check for clogging or residue in detergent drawer |
| F9 E1 | Excessive drain time | Ensure drain hose is not blocked and properly installed |
| Drn | Draining issue | Ensure proper hose installation |
| HC | Hot and cold hoses reversed | Swap hoses to correct installation |
| LdL | Lid cannot lock | Check for obstructions |
| LdU | Lid cannot unlock | Remove items on top of lid |
| LF, Lo FL, F8 E1 | Fill cycle takes too long | Ensure active water supply and check inlet valve filters |
| Lid | Lid left open | Close the lid |
| Ofb | Unbalanced load | Redistribute laundry evenly |
| OL | Overloaded washer | Remove several items from the drum |
| PF | Power failure | Hold Start or Power button for ten seconds |
| Sud | Excessive suds | Manually drain washer and ensure correct detergent usage |
Maytag front loader and top loader models covered
A101, A102, A102S, A103, A103S, A104, LAT9416AAE, MAH3000AWW, MAH4000AWW, MAH5500BWW, MAH8700AWW, MAV6200AWW, MAV7600AWW, MHWE200XW00, MVWC300VW1, MVWC415EW2, MVWC6ESWW1, MVWX655DW1, PAV2200AWW, PAV2300AWW, PAVT234AWW.
How to Read Maytag Washer Error Codes
1. Check the Display Panel:
Error codes appear on the display panel of your Maytag washer, usually as a combination of letters and numbers. The error code is often displayed when there’s an issue with the washing machine’s operation.
2. Locate the Owner’s Manual:
Consult your Maytag washer’s manual, which usually includes a section dedicated to troubleshooting error codes. The manual will describe each error code, the probable causes, and possible solutions.
3. Power Cycle the Washer:
If you notice an error code, start by turning off the washer and unplugging it for about 30 seconds. This can reset the system. The error code is often displayed when there’s an issue with the washing machine’s operation.
4. Perform a Diagnostic Check:
Some Maytag washers have a diagnostic mode where error codes can be checked directly. Consult your manual to enable this mode. During this mode, the washer will run a series of tests and display the codes, which correspond to specific problems.
Error codes in Maytag top load washers
- Drn: Draining issue. Ensure the washer hose installation is correct.
- HC: Hot and cold inlet hoses installed in reverse. Swap the hoses so that each is connected to the correct inlet.
- LdL: Lid cannot lock. Check for any obstructions preventing the lid from locking properly.
- LF, Lo FL, F8 E1: Fill cycle takes too long. Ensure water supply is active and check inlet valve filters for blockages.
- Lid: Lid left open. Close the lid to clear the code.
- LdU: Lid cannot unlock. Remove items placed on top of the lid.
- Ofb: Unbalanced load. Redistribute the load evenly.
- OL: Oversized load. Remove several items and restart the cycle.
- PF: Power failure. Hold the Start button or Power button (varies by model) for ten seconds to restart.
- Sud: Excessive suds. Manually drain the washer and ensure you are using the correct detergent.
Error Codes in Maytag Front Load Washers
- LOC or LC: Control Lock activated. Press the Control Lock button or check the Owner’s Manual for specific instructions on how to deactivate it.
- dET: Detergent cartridge not detected. Ensure the cartridge is inserted correctly or ignore this message if you are using single-load doses of detergent.
- INT: Cycle was paused or canceled. Press the Pause or Cancel button twice and then the Power button once. If the code persists, unplug the washer for one minute.
- rL or F34: Items detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the cycle.
- Sud or Sd: Excessive suds. The washer will automatically pause the tumbling and add extra rinse water. Ensure you are using HE detergent and check the drain hose for clogs.
- F5 E2: Door not locking properly. Check for obstructions or ensure the door is closing completely. Press the Pause or Cancel button twice and then the Power button once to clear the code.
- F7 E1: Motor speed sensing error. Check for remaining shipping bolts and ensure the load is not overloaded. Press the Pause or Cancel button twice and then the Power button once.
- F8 E1 or LO FL: Low water flow. Ensure faucets are turned on fully and that water inlet hoses are not kinked or clogged. Press the Pause or Cancel button twice and then the Power button once.
- F8 E2: Dispenser system error. Verify that the detergent drawer or cartridge is not clogged. Press the Pause or Cancel button twice and then the Power button once.
- F9 E1: Excessive drain time. Check the drain hose for kinks or clogs and ensure it is properly installed. Press the Pause or Cancel button twice and then the Power button once.
When to call a professional
If you’re unable to resolve the issue after following the troubleshooting steps above, it’s advisable to reach out to ARS Repair Inc.. Our experienced technicians specialize in diagnosing and fixing problems with Maytag washers and can quickly determine the cause of any error code you encounter. Whether it’s a simple fix or a complex repair, our team is here to help.
To schedule a repair or inquire about our services, contact ARS Repair Inc. today.
We’re ready to assist you with all your appliance repair needs, ensuring your Maytag washer is back to working efficiently in no time.